+- Stresslinux community (https://www.stresslinux.org/community)
+-- Forum: Stresslinux Main (https://www.stresslinux.org/community/forumdisplay.php?fid=1)
+--- Forum: General discussion (https://www.stresslinux.org/community/forumdisplay.php?fid=2)
+--- Thread: Problem: boot with Oops (/showthread.php?tid=16)
Problem: boot with Oops - tlehmann - 03-20-2007
Hallo *!
- So when i boot my computer from stresslinux-0.3.1.iso,
system say Oops...(s.dmesg_boot)
- the system is very unstable there after.
- GDT finds a RAID-Controller. Typically however the driver should
be used megaraid_sas. (s. dmesg_boot)
- stresslinux-0.3.1 used linux-2.6.16.18
Can someone help?
In the meantime does a newer version exist?
regards Torsten
----------------------------------------------------------------------------
- system:
Platinium 5210R
E7501HG2
Chipset: Intel E7501
Memory: 4GB ECC (4x1G)
Linux stress 2.6.16.18 #1 SMP Fri May 26 22:17:25 CEST 2006 i686 unknown
- dmesg_boot
root@stress:~# dmesg | more
4288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
...
Adaptec aacraid driver (1.1-4 May 26 2006 22:23:52)
libata version 1.20 loaded.
scsi: <fdomain> Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.04
GDT-HA: Found 1 PCI Storage RAID Controllers
Configuring GDT-PCI HA at 3/1 IRQ 28
GDT-HA 0: Name: SRCZCR
scsi4 : SRCZCR
Vendor: Intel Model: Host Drive #00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 286695990 512-byte hdwr sectors (146788 MB)
sda: Write Protect is off
sda: Mode Sense: 0c 00 00 08
sda: got wrong page
sda: assuming drive cache: write through
SCSI device sda: 286695990 512-byte hdwr sectors (146788 MB)
sda: Write Protect is off
sda: Mode Sense: 0c 00 00 08
sda: got wrong page
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 4:0:0:0: Attached scsi disk sda
sd 4:0:0:0: Attached scsi generic sg2 type 0
Vendor: ESG-SHV Model: SCA HSBP M15 Rev: 0.10
Type: Processor ANSI SCSI revision: 02
4:1:6:0: Attached scsi generic sg3 type 3
Vendor: ESG-SHV Model: SCA HSBP M15 Rev: 0.10
Type: Processor ANSI SCSI revision: 02
4:2:5:0: Attached scsi generic sg4 type 3
imm: Version 2.05 (for Linux 2.4.0)
ipr: IBM Power RAID SCSI Device Driver version: 2.1.2 (February 8, 2006)
Emulex LightPulse Fibre Channel SCSI driver 8.1.1
Copyright(c) 2004-2005 Emulex. All rights reserved.
megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)
megaraid: 2.20.4.7 (Release Date: Mon Nov 14 12:27:22 EST 2005)
nsp32: loading...
osst :I: Tape driver with OnStream support version 0.99.3
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
ppa: Version 2.07 (for Linux 2.4.x)
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase=
and irq= options<6>st: Version 20050830, fixed bufsize 32768, s/g segs 256
sym53c416.c: Version 1.0.0-ac
sym0: <895> rev 0x1 at pci 0000:01:09.0 irq 17
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: suspicious SCSI data while resetting the BUS.
sym0: dp1,d15-8,dp0,d7-0,rst,req,ack,bsy,sel,atn,msg,c/d,i/o = 0x109, expecting
0x100
sym0: FATAL ERROR: CHECK SCSI BUS - CABLES, TERMINATION, DEVICE POWER etc.!
sym0: giving up ...
Failed initialization of WD-7000 SCSI card!
ReiserFS: sr0: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on s
r0
VFS: Can't find ext3 filesystem on dev sr0.
VFS: Can't find an ext2 filesystem on dev sr0.
XFS: bad magic number
XFS: SB validate failed
ISO 9660 Extensions: RRIP_1991A
st: Unloaded.
osst :I: Unloaded.
nsp32: unloading...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
printing eip:
c041a44d
*pde = 00000000
Oops: 0000 [#1]
SMP
Modules linked in: pdc202xx_old hpt366 pdc202xx_new cs5520 hpt34x gdth dmx3191d
dc395x atp870u ata_piix ahci libata aha152x aacraid a100u2w BusLogic winbond_84
0 dmfe de4x5 de2104x sungem sungem_phy sundance s2io natsemi ixgb hp100 fealnx d
grs depca 8139cp 3c509
CPU: 0
EIP: 0060:[<c041a44d>] Not tainted VLI
EFLAGS: 00010246 (2.6.16.18 #1)
EIP is at scsi_allocate_request+0x37/0x51
eax: f7d242b0 ebx: 00000000 ecx: 00000000 edx: f7d24200
esi: 00000000 edi: f7d24360 ebp: c0710294 esp: f73c9d3c
ds: 007b es: 007b ss: 0068
Process rmmod (pid: 4486, threadinfo=f73c8000 task=f6c27a70)
Stack: <0>00000000 f73c9f34 f9dc1a0c 00000000 f6c27a70 dfd81c30 c3010060 000000
00
...
- test_tools
root@stress:~# fdisk -l /dev/sda
root@stress:~#
- keine HD gefunden
root@stress:~# ls /proc/scsi/
Segmentation fault
- Probleme mit proc-fs
root@stress:~# lshw
SCSI
- lshw hang, ssh-connection broken
Mem: 55032K used, 3836520K free, 0K shrd, 6892K buff, 19016K cached
Load average: 1.72, 0.67, 0.24 (State: S=sleeping R=running, W=waiting)
PID USER STATUS RSS PPID %CPU %MEM COMMAND
13019 root D 3120 9277 0.0 0.0 lshw
13369 root D 3116 9277 0.0 0.0 lshw
6654 root S 1624 2443 0.0 0.0 sshd
9555 root S 1588 2443 0.0 0.0 sshd
9277 root S 1424 6672 0.0 0.0 bash
----------------------------------------------------------------------------